一级淫片免费视频-一级淫片在线观看-一级在线 | 欧洲-一级在线观看视频-美女一级牲交毛片视频-美女伊人网

首頁 產品展示>Perkins珀金斯850-854F柴油發動機T412697汽缸蓋墊片

Perkins珀金斯850-854F柴油發動機T412697汽缸蓋墊片

Perkins珀金斯850-854F柴油發動機T412697汽缸蓋墊片供應商,Perkins珀金斯850-854F柴油發動機T412697汽缸蓋墊片技術價格規格咨詢服務,Perkins珀金斯850-854F柴油發動機T412697汽缸蓋墊片零配件供應,Perkins珀金斯850-854F柴油發動機T412697汽缸蓋墊片售后服務中心,Perkins珀金斯850-854F柴油發動機T412697汽缸蓋墊片,Perkins珀金斯850-854F柴油發動機T412697汽缸蓋墊片詳細的技術參數,
產品咨詢

詳細描述

項目   零配件號碼    最新件號   描述  

    1      1      汽缸蓋總成       

    25     1      汽缸蓋墊片       

    (25)   T411894    1   T411894    汽缸蓋墊片       

    (25)   T412697    1   T412697    汽缸蓋墊片       

    26  T412677    4   T412677    汽缸蓋螺拴       

    27  T412687    6   T412687    汽缸蓋螺拴       

    28  T412947    8   T412947    圖釘         

    29  T411791    1   T411791    合釘  

A special service version of the tamper evident body (D) must be fitted when a new fuel screw is fitted. A kit

part number U5MK0619 is available from PDC. This kit will be supplied only to permitted personnel and must

not be supplied to end users. A groove (D4) around the circumference of the tamper evident body is used to

identify it as a service part.

2  Fit the fuel adjustment screw assembly (C3) to the engine ensuring that there is a metal snap ring (C1)

located in the lock nut groove and a o-ring (C2) fitted.

3  On a suitable calibrated test facility, reset the engine performance parameters to the certified specification

indicated on the engine's emissions control information label mounted on the timing case.

4  Having set the full load fuel delivery to the certified specification and ensuring the lock nut is correctly

tightened, insert the D-plug (D2) into the service tamper resistant body (D3) at the opposite end of the internal

groove (D1). Fit the new service tamper resistant body assembly (D) over the fuel adjustment screw.

5  Tap on the tube until the internal groove (D1) in the body engages over the metal snap ring (C1) in the lock

nut.

To remove and re-fit the tamper evident maximum engine speed cap

The maximum speed adjustment has a plastic cap (B4) fitted by Perkins. The length of this fitted cap will be

either 22mm or 30mm in length depending on the original protrusion of the maximum speed adjustment screw

(B5). The cap is pressed by hand onto the adjustment screw and an internal lip locates into a groove on the

lock nut.

1  Remove the plastic cap (B4) from the maximum speed bolt (B5) with a suitable lever, taking care not to

damage the seal between the cylinder block and the locknut.

2  Make the necessary adjustment to maximum (no load) engine speed by rotating bolt clockwise to reduce

speed and anti-clockwise to increase speed with the engine throttle lever fully open.

Note:   The only permitted adjustment to the maximum engine speed is to correct the speed in accordance with

the high idle speed shown on the emissions compliance label mounted on the engine timing case.

3  After adjustment to within the certified maximum speed range, a new service cap of the appropriate length

can be obtained from PDC Irlam. The replacement service cap will be red in colour part number 131276440 -

30mm length or 131276450 - 22 mm length. This cap will be supplied only to permitted personnel and must

not be supplied to end users.

4  Hand press the replacement service cap onto maximum speed bolt (C4) lock nut.

A warranty claim will not be accepted if it can be seen that an adjustment to the maximum engine speed setting

(B5) or the fuel adjustment screw (B2) has been made by personnel not approved by Perkins.

1

2

3

4

1

3

2

4

c

C

D

74

Workshop Manual, TPD 1377E, issue 4

This document has been printed from SPI². Not for Resale


 

6

100 Series

Idler gear and oil pump

To remove and to fit

Operation 6-10

Special requirements

Clearance (B1) mm (in)

Standard

Service limit

0,01 - 0,15 (0.0004 - 0.0060)

0,25 (0.0098) max

Extra shims may be required to achieve the standard clearance. To check the end float refer to Operation 6-13.

1

Workshop Manual, TPD 1377E, issue 4

75

This document has been printed from SPI². Not for Resale


 

6

100 Series

Idler hub

To fit

Operation 6-11

Special requirements

Special tools

Description

Part number

21825624

Idler hub assembly tool - 102-05, 103-07

Idler hub assembly tool - 103-10

21825625

Idler hub assembly tool - 103-13, 103-15,

104-19, 104-22

21825626

Caution:  If the idler hub is removed, it must be renewed.

76

Workshop Manual, TPD 1377E, issue 4

This document has been printed from SPI². Not for Resale


 

6

100 Series

Gear teeth backlash

To check backlash

Operation 6-12

Special requirements

Timing gear tolerances mm (in)

Standard

Service limit

0,08 (0.0032)

0,25 (0.0098)

1  Align the set marks.

2  Measure the clearance with a feeler gauge.

Workshop Manual, TPD 1377E, issue 4

77

This document has been printed from SPI². Not for Resale


 

免費熱線
400-082-9096?
整機銷售
0731-84424871? 18374999699
售后維修
0731-84424872? 15580888444
配件銷售
0731-84424873? 18274802060
手機端
微信公眾號
主站蜘蛛池模板: 人人澡人 | 毛片又大又粗又长又硬 | 久久6免费视频 | 青青青青久久精品国产h | 77788色淫免费网站视频 | 1314亚洲人成网站在线观看 | 91精选视频在线观看 | 视频二区在线观看 | 午夜欧美福利视频 | 免费一级毛片在线播放不收费 | 在线观看886影院成人影院 | 亚洲国产成人久久 | 一级片aaaaaa| 国模沟沟一区二区三区 | 男人天堂网在线观看 | 欧美特黄特色aaa大片免费看 | 天天干天天爱天天射 | 天天干夜夜操 | 日韩免费三级 | 欧美黄色片 一级片 | 国产在线观看午夜不卡 | 亚洲欧美一区二区三区另类 | 如果我们是季节韩剧在线观看 | 天天综合色天天桴色 | 国产精品资源网站在线观看 | 国产三级在线 | 一级毛片aaa片免费观看 | 一级特黄aaa大片免色 | 成熟女人免费一级毛片 | 久久狠色噜噜狠狠狠狠97 | 激情综合丝袜美女一区二区 | 亚洲成a人片在线观看88 | 亚洲 欧美 精品 | 中国业余老太性视频 | 亚洲线精品一区二区三区 | 亚洲综人网 | 国产精品福利一区二区亚瑟 | 免费在线观看视频网站 | 日本加勒比在线视频 | 国产清纯白嫩大学生正在播放 | 久久综合操|