一级淫片免费视频-一级淫片在线观看-一级在线 | 欧洲-一级在线观看视频-美女一级牲交毛片视频-美女伊人网

首頁 產品展示>Perkins珀金斯1506A柴油發動機T400950渦輪增壓器

Perkins珀金斯1506A柴油發動機T400950渦輪增壓器

Perkins珀金斯1506A柴油發動機T400950渦輪增壓器供應商,Perkins珀金斯1506A柴油發動機T400950渦輪增壓器技術價格規格咨詢服務,Perkins珀金斯1506A柴油發動機T400950渦輪增壓器零配件供應,Perkins珀金斯1506A柴油發動機T400950渦輪增壓器售后服務中心,Perkins珀金斯1506A柴油發動機T400950渦輪增壓器,Perkins珀金斯1506A柴油發動機T400950渦輪增壓器詳細的技術參數,
產品咨詢

詳細描述

項目   零配件號碼        新件號 描述  

    1   T400950    1   T400950    渦輪增壓器       

    (1) T400950R   1   T400950R   渦輪增壓器 -交換        

    5   T400948    1   T400948    密封墊片 -渦輪增壓器       

    6   CH11242    4   CH11242    鎖緊螺母

Peregrine EDi and 1300 Series EDi

5  Remove the container and dispose of the fluids safely in accordance with local regulations.

6  Remove the rocker cover, see Operation 3-1.

7  Remove the screws that retain the plate for the electrical cables, and remove the plate (C).

8  Remove the front setscrew (D) from the clamp that retains the injector unit.

C

D

W218

W219

Caution: Do not remove the rear shouldered setscrew (E1), it is not necessary to do so.

9  Tilt the clamp (F) until it is free from the rear shouldered setscrew.

1

E

F

W220/1

W221/1

Continued

Workshop Manual, TPD 1353E, Issue 3

167

This document has been printed from SPI². Not for Resale


 

11

Peregrine EDi and 1300 Series EDi

10  Push the clamp toward the rear of the engine (G).

11  Use a lever (H) to carefully raise the injector unit.

12  Remove the injector unit.

13  Remove and discard the ‘O’ rings and the washer, see Operation 11-4.

G

H

W222

W223

168

Workshop Manual, TPD 1353E, Issue 3

This document has been printed from SPI². Not for Resale


 

11

Peregrine EDi and 1300 Series EDi

To fit

Operation 11-3

1  Renew the injector unit seals and washer, see Operation 11-4.

2  Carefully insert the injector unit into its sleeve; ensure that the clamp (A1) is aligned to allow the shouldered

rear setscrew (A2) to pass through it.

3  Push the injector unit down (A) until it is on its seat.

4  Tilt the clamp (B) until it is past the head of the rear setscrew.

1

A

2

B

W224/1

W221

5  Push the clamp towards the front of the engine (C) until it engages the rear shouldered setscrew and aligns

with the hole for the front setscrew.

6  Fit the front setscrew (D) and tighten it to 13 Nm (10 lbf ft) 1,3 kgf m.

C

D

W220

W219

Continued

Workshop Manual, TPD 1353E, Issue 3

169

This document has been printed from SPI². Not for Resale


 

11

Peregrine EDi and 1300 Series EDi

7  Fit the plate for the injector unit cables (E).

8  Fit the rocker cover, see Operation 3-2.

9  Fit a new ‘O’ ring (F1) to the drain plug and fit the plug (F2) into the gallery in the supply manifold (F3).

1

2

3

E

F

W218

W212

10  Fit the valve (G1) for the fuel return pipe and tighten it to 35 Nm (26 lb ft) 3,6 kgf m.

11  Fit new copper washers to the banjo union (G3) of the fuel return pipe, fit and tighten the banjo bolt (G2)

to 35 Nm (26 lb ft) 3,6 kgf m.

12  Eliminate air from the fuel system, see Operation 11-9.

1

2

3

G

W213

170

Workshop Manual, TPD 1353E, Issue 3

This document has been printed from SPI². Not for Resale


 

11

Peregrine EDi and 1300 Series EDi

To renew the fuel injector unit seals

Operation 11-4

To remove the old ‘O’ ring seals and seal rings

1  Remove the injector units, see Operation 11-2.

2  Remove the washer (A6) from the injector unit nozzle - copper for WK, WL, WM, and WN engines; stainless

steel for WP, WQ, WR, and WS engines.

Cautions:

l  ‘O’ rings and seals must be renewed each time a fuel injector is removed.

l   If any of the injector units have damaged ’O’ rings or seals, then all injector units must be removed and

checked.

l   During removal of the ‘O’ rings, be careful to avoid damage to the body of the injector unit or the grooves

for the seals.

3  With the use of a suitable smooth tool, lift the lower ‘O’ ring (A5) (orange) out of its groove. Cut the seal and

remove it.

4  Lift the middle seal (A4) (blue and black) out of its groove with the same smooth tool, cut and remove it.

5  Lift the upper ‘O’ ring (A3) (blue), cut and remove it.

6  Lift the rubber ring (A2) (black), cut and remove it.

7  Carefully remove the split ring (A1) (steel).

6

5

3

2

4

1

A

W225/1

Workshop Manual, TPD 1353E, Issue 3

171

This document has been printed from SPI². Not for Resale


 

11

Peregrine EDi and 1300 Series EDi

To fit the ‘O’ rings and ring seals

Ensure the injector unit is clean, then fit the new seals in the sequence below:

Caution: All ‘O’ rings and seals and the injector unit must be lightly lubricated with new clean engine lubricating

oil before the ‘O’ rings and seals are fitted.

1  Carefully slide the split ring (B1) (steel) over the injector body and into its groove.

2  Carefully slide the rubber ring (B2) (black) over the injector body until it fits into its groove - ensure that the

ring is not damaged.

3  Carefully slide the lubricated ‘O’ ring (B3) (blue) over the injector body until it fits into its groove.

4  Carefully slide the lubricated seal (B4) (blue and black) over the injector body until it fits into its groove.

5  Carefully slide the lubricated lower ‘O’ ring (B5) (orange) over the injector body until it fits into its groove.

6  Fit the washer (B6) to the injector unit:

l   copper for WK, WL, WM, and WN engines;

l   stainless steel for WP, WQ, WR, and WS engines.

7  The injector units are now ready to be fitted, see Operation 11-3.

6

5

3

2

4

1

B

W225/1

172

Workshop Manual, TPD 1353E, Issue 3

This document has been printed from SPI². Not for Resale


 

11

Peregrine EDi and 1300 Series EDi

Fuel lift pump

To remove and to fit

Operation 11-5

To remove

Note: The fuel lift pump is fitted to the side of the high-pressure pump.

1  Remove the banjo bolts (A1 and A5) from the fuel pipes and discard the washers (A2 and A4).

2  Release the nuts (A3) and remove the pump (A6).

3  Remove and discard the joint.

To fit

1  Clean the joint face on the fuel lift pump and on the high-pressure pump.

Note: Ensure that the eccentric on the camshaft of the high-pressure pump is in the minimum lift position. If it

is not, rotate the crankshaft until it is.

2  Fit a new joint to the lift pump.

3  Check that the push rod (Operation 11-6/A12) is in position and fit the lift pump to the high-pressure pump.

4  Fit and tighten the nuts (A3) gradually and evenly to 6 Nm (4 lbf ft) 0,6 kgf m.

5   Connect the fuel pipes to the fuel lift pump, fit new copper washers (A2 and A4) to the banjo bolts (A1 and

A5). Tighten the banjo bolts to 35 Nm (26 lbf ft) 3,6 kgf m.

3

5

1

4

2

A

6

W129/1

Workshop Manual, TPD 1353E, Issue 3

173

 

免費熱線
400-082-9096?
整機銷售
0731-84424871? 18374999699
售后維修
0731-84424872? 15580888444
配件銷售
0731-84424873? 18274802060
手機端
微信公眾號
主站蜘蛛池模板: 欧美日韩免费大片 | 免费在线观看大片影视大全 | 久久久久久国产精品mv | 综合色图 | 婷婷色站 | 一级黄色录像毛片 | 狠狠色噜噜狠狠狠狠米奇7777 | 一级特黄aa大片免费播放视频 | 小雪被老外黑人撑破了 | 女性私密部位扒开的视频 | 精品国产成人系列 | 日本怡红| 天天做夜夜做 | 国产精品久久永久免费 | 四虎院影永久在线观看 | 二区三区视频 | 国产三级精品三级 | 综合五月婷婷 | 精品国产柚木在线观看 | 性欧美丨18一19 | 久久久精品午夜免费不卡 | 亚洲国产精品久久久久婷婷老年 | 欧美一级特黄高清免费 | 天天干天天操天天做 | 久久久99精品免费观看精品 | 8888奇米四色在线 | 深夜视频在线 | 国内精品免费视频精选在线观看 | 美女扒开尿口给男人看的让 | 4hc44四虎www在线影院男同 | 在线免费成人网 | 蜜色网| 亚洲人成人| 91寡妇天天综合久久影院 | 黄色成人免费网站 | 亚洲美女精品 | 日本三级欧美三级香港黄 | 免费黄色欧美 | 黄色大片在线免费观看 | 全部免费特黄特色大片视频 | 国产成人精品系列在线观看 |